Inrush, Peak and Min Max on a Clamp Meter
On this page
Quick answer Inrush, peak, Min Max and display hold can preserve different quantities. Identify the signal processing, trigger and time interval for the exact instrument before comparing results. A function name alone leaves essential information about the captured number unresolved.
Name the quantity each function preserves
A clamp meter processes a changing electrical signal before presenting a value. One function may retain a waveform's extreme amplitude, another may retain the highest processed RMS result, and another may simply freeze the displayed reading.
The True RMS clamp-meter guide explains the waveform and bandwidth context. Continue that review by asking what each recording feature does with the processed signal.
| Feature | Quantity to identify in the manual | Essential timing question |
|---|---|---|
| Inrush | The defined startup-capture result | What triggers acquisition and what interval is evaluated? |
| Peak | The supported waveform extreme or other specifically defined peak output | What pulse width, response and bandwidth are supported? |
| Min Max | Extrema of the instrument's specified processed readings | How often are those values evaluated and when does the session reset? |
| Hold | The displayed value selected for freezing | What manual or automatic condition freezes it? |
Use the exact definition where a maker uses a label differently. Preserve the measured quantity and processing conditions in the report.
Read a documented capture implementation
The Fluke 353/355 manual illustrates a 100 ms interval in its inrush diagram and lists range-dependent inrush trigger levels. This gives one identified implementation to examine. Confirm the corresponding quantity, trigger and interval for the actual model selected for the job.
Hioki's CM4001 complete manual separately describes its maximum, minimum and average RMS readings alongside peak outputs. Its inrush function is specifically AC, and the manual states that it cannot measure inrush containing DC components accurately. The signal type belongs in the capability review.
A meter's ordinary display update rate supplies another timing field. Obtain the capture function's own response and processing description. A fast-looking screen and a documented short-event capture address different parts of the measurement chain.
Work through an ideal pulse before interpreting a report
Consider a constructed mathematical pulse that is 10 A for 20 ms and zero for the remaining 80 ms of a 100 ms interval. Its peak amplitude is 10 A. Its arithmetic mean over that interval is 2 A.

The RMS calculation squares the values, averages those squares over the stated interval and takes the square root.
RMS = sqrt((10² × 20 + 0² × 80) / 100) = sqrt(20) ≈ 4.47 A
The pulse height, mean and interval RMS are three different properties of the same selected waveform. If the RMS interval covered only the flat 20 ms pulse, that particular interval's RMS would be 10 A. The stated window changes the mathematical question.
This is a teaching waveform with a DC component. It represents no observed startup or actual meter algorithm, and an AC-only mode may require another signal model. Use the calculation to ask precise capability questions rather than predict what an unidentified inrush function will display.
Investigate two different startup numbers
First check whether both records concern the same physical event and operating condition. Then compare the retained quantity, AC/DC response, range, filter, trigger, capture window and reset state. Different processing can produce different values without either record describing the same quantity.
If one record says peak and the other says inrush RMS, retain those identities separately. If both claim the same quantity, verify whether their triggering and intervals match. Review unresolved overload or capture warnings before comparing the values with an equipment requirement.
For Min Max, establish when the session began and which observations it includes. A retained maximum from earlier operation can remain visible during a later event. A manually held display needs its own time and state recorded.
Use a suitable controlled signal and documented reference when qualifying a capture function. Any equipment startup or circuit connection must follow the approved electrical procedure and qualified operator's plan. The report review here supplies no switching sequence for live work.
Check product feature claims against the required output
The current ETCR6200 listing mentions inrush applications, peak hold, display hold and data storage. It lists a two-per-second sampling rate. The exact startup trigger, capture interval and peak-response definition still need the supplied manual or written capability evidence.
Ask for a sample report from the required function and an explanation of every retained value. Confirm whether the original waveform is available when the task requires it. A stored number can satisfy a defined amplitude question while leaving event shape and duration to another compatible recording method.
Specify capture requirements before choosing a meter
Write the event, expected signal type and duration, required quantity, minimum pulse width, bandwidth, range, trigger and retained records. Add the relevant reference or equipment acceptance rule. Keep a startup RMS requirement separate from a waveform-crest requirement.

Compare the Mcooh clamp-meter options against that request. Preserve model, mode, settings, event identity, capture conditions and result units together so a later reviewer can determine what the recorded current actually represents.