Test & measurement instruments

Measuring Thin Anodized Layers on Aluminum

By Mcooh TeamPublished 4 minute read
Evaluate thin anodized aluminum layers with representative substrate references, a suitable eddy-current probe and a clear accuracy budget.
Coating thickness gauge and aluminum reference on a metrology bench

Quick answer A suitable eddy-current coating probe can measure a nonconductive anodic layer over aluminum. For thin layers, evaluate its accuracy expression at the actual thickness, the conductivity and geometry of the substrate reference, and the documented calibration conditions. A fine display increment alone provides too little information to judge fitness for an acceptance limit.

Confirm the layer and the measurement method

An anodized part presents a particular measurement system. The instrument senses a nonconductive oxide layer over a conductive aluminum base. Confirm that construction from the process record, especially when paint, sealers or additional surface treatments are present. Establish which physical layer the required thickness describes.

The public scope of ASTM B244-09(2021) covers eddy-current measurement of suitable nonconductive coatings on nonmagnetic base metals and identifies anodic coatings on aluminum as a particular application. It also excludes chemical conversion coatings as too thin for that method. Obtain the current procedure required by the job before making an acceptance decision.

The Fe/NFe coating measurement guide explains the underlying substrate distinction. For a thin anodized layer, continue that selection by evaluating the actual aluminum reference and the size of the permitted error at the target thickness.

Match the substrate reference to the production part

The B244 public significance statement requires the calibration-adjustment reference and coated article to have the same substrate conductivity. An arbitrary aluminum plate therefore needs a documented suitability check. Alloy identity and production condition help identify a representative reference, while the measurement procedure governs how its conductivity match is established.

Illustrative nonferrous and ferrous coating reference setup

Also preserve the shape, thickness and usable contact area that affect the selected probe. A broad, flat supplied plate may respond differently from a thin curved profile. Where possible, retain a suitable uncoated production sample with known identity and representative geometry. Keep its reference surfaces clean and protected.

Separate a reference mismatch from an instrument problem. If the gauge behaves consistently on its assigned standard but changes on a different bare profile, investigate the substrate and geometry before changing the instrument response. An adjustment needs an identified application and permitted method.

Calculate the specification at the thickness of interest

The current LS225 with N1500 probe is a relevant candidate for nonconductive coatings, including anodic oxide, over compatible nonferromagnetic metal. Its published accuracy expression is ≤±(2%H + 0.3 µm) after five-point calibration, with H defined as the standard or reference thickness.

The following calculations apply that expression to hypothetical reference values. They illustrate specification arithmetic. They provide no observed performance data or proof that a particular thin coating can meet a production requirement.

Hypothetical H Calculation of magnitude Magnitude relative to H
2 µm 0.02 × 2 + 0.3 = 0.34 µm 17%
20 µm 0.02 × 20 + 0.3 = 0.70 µm 3.5%

At both values the stated display resolution is 0.1 µm. The fixed 0.3 µm term makes a larger relative contribution at the thinner reference. Compare the calculated magnitude with the actual tolerance and decision rule before selecting the equipment.

Keep the specification limit separate from a complete measurement uncertainty evaluation. Reference uncertainty, substrate effects, placement and other applicable influences still require treatment in the approved method. Averaging repeated values also needs its own justification and cannot simply divide away every source of error.

Keep accuracy and fixture repeatability conditions visible

The same product lists repeatability of ≤±(0.8%H + 0.1 µm) with a matching fixture. That condition addresses repeated results under the specified arrangement. Use the accuracy expression, its calibration condition and the relevant uncertainty evaluation when judging closeness to a reference.

A fixture can help maintain consistent probe placement on a small profile. Select it together with the part support and access needed to place the probe squarely. The N1500 configuration lists a minimum measuring area of 7 mm diameter and separate curvature limits, so an accessible edge or narrow rib needs explicit suitability review. The optional fixture is a separate accessory.

A new fixture or contact arrangement changes part of the setup. Recheck the reference response using that arrangement. Retain which fixture, orientation and contact face produced the results so another operator can reproduce the comparison.

Verify a useful thickness range before evaluating parts

Use the coating gauge verification and adjustment workflow for the general control sequence. Add the representative aluminum reference and known thicknesses relevant to the anodizing task. A zero response evaluates one condition. Known nonzero references challenge performance where the thickness decision will be made.

LS225 coating thickness gauge with separate probe

The LS225 V2.16 manual supports zero adjustment and one- to five-point calibration. Its specified accuracy condition uses five points. Follow the actual manual and approved reference plan rather than treating every available adjustment option as equivalent evidence.

For diagnosis, retain the observations before adjustment. Consistent deviation across references suggests a different investigation from erratic placements on one curved face. Check cleanliness, seating, reference identity and selected setup, then repeat the appropriate verification. Persistent failure needs the quality procedure's disposition before affected parts are accepted.

Build an anodizing-specific equipment request

Send the supplier the aluminum alloy and condition, required oxide-thickness range and tolerance, profile drawing, accessible contact faces and representative uncoated material. Include the proposed references and the governing inspection method. Request evidence from the exact probe and support configuration when the layer approaches the practical limits of the measurement system.

Use the Mcooh thickness gauge collection to identify candidates against those requirements. Keep the resulting method record tied to the probe, reference materials, adjustment state, verification results and part locations. That record connects the displayed value to the specific anodized-aluminum decision.

More from Thickness Gauge Guides

Need help choosing an instrument?

Tell us what you need to measure, the range and the application. You can also browse our measurement guides.