Measuring Paint and Zinc Layers on Galvanized Steel
On this page
Quick answer Paint over galvanized steel creates a layer system containing paint, zinc and the steel base. A conventional magnetic indication can represent the combined paint-and-zinc distance. Separate layer results require a supported duplex method or a controlled comparison with correctly matched observations and a valid measurement model.
Name the three thickness quantities
Start with a drawing of the layer stack. The American Galvanizers Association describes painting over galvanized steel as a duplex system. Its coating-measurement discussion also explains that magnetic instruments respond to several kinds of coatings over steel. Identify the actual construction through the component and process records.
For a simple paint-over-zinc stack, distinguish paint thickness, zinc thickness and their combined thickness. Record which one the specification requires at each inspection stage. The Fe/NFe method guide provides the substrate and sensing-principle background.
| Reported quantity | Physical interval | Typical question |
|---|---|---|
| Paint thickness | Paint surface to the zinc interface | Does the applied paint meet its coating requirement? |
| Zinc thickness | Zinc surface to the steel interface | What zinc layer remains under the evaluated preparation? |
| Combined coating thickness | Paint surface to the steel interface | What complete coating distance is being sensed above steel? |
An instrument record should name the quantity beside the value. Retain the material, stage and location so a later reader can distinguish an unpainted zinc measurement from a finished duplex measurement.
Understand the conventional magnetic indication
A magnetic coating gauge responds to the ferromagnetic base beneath suitable nonmagnetic layers. When zinc and paint both separate the probe from the steel, the sensed distance can include both layers. Its calibration, substrate response, geometry and surface condition still govern the result.
An automatic Fe/NFe label identifies a sensing condition selected by the instrument. A separate pair of paint and zinc values requires documented layer-resolving capability. Obtain the manufacturer's explanation of each displayed channel and its application envelope before assigning a layer name.
The current LS225 with F500 magnetic probe is an example for compatible nonmagnetic coatings, including zinc, over ferromagnetic metal. It can be considered for a suitable unpainted-zinc measurement stage. Review the complete layer stack and probe conditions before extending that interpretation to a finished painted part.
Preserve location identity in before-and-after measurements
A before-painting zinc map can support a later paint-thickness comparison when the procedure preserves the corresponding locations and the zinc condition. Define those assumptions before collecting data. Preparation, abrasion, repair or further processing can change the coating present at a point.
Use a part drawing, point identifiers and the same controlled method to connect the two stages. Record the zinc result before painting and the combined result after painting for each corresponding location. Keep uncertainty, repeat placements and the required sampling interpretation with both observations.
Consider a hypothetical example. Zinc at point A is 62 µm and zinc at point B is 85 µm before painting. The finished combined result at B is 132 µm. Under an approved unchanged-zinc and compatible-measurement model, the corresponding difference at B is 132 − 85 = 47 µm.
Using the zinc value from A instead would produce 132 − 62 = 70 µm. The extra 23 µm comes from mixing locations with different zinc thicknesses. These selected numbers illustrate the pairing problem. Actual layer acceptance requires the applicable method and real observations.
A whole-part average zinc value also describes an aggregate. Its subtraction from a local finished value introduces a spatial assumption. State that assumption and evaluate whether it fits the inspection question before using the result as a local paint thickness.
Recognize a documented duplex measurement system
A specialized duplex instrument can combine complementary sensing responses at the same measurement location. DeFelsko's current FNDS documentation provides one identified example. Its duplex mode measures the combined paint/zinc thickness magnetically, measures paint over zinc with an eddy-current response, and derives zinc from the difference.
The same documentation identifies separate bare-steel and unpainted-zinc reference conditions. It specifies a minimum zinc thickness of 13 µm for that probe. These are properties of the named system and its procedure. Confirm the equivalent requirements for whichever model is proposed for your work.
A valid dual-layer result therefore depends on more than having both Fe and NFe symbols available. Review the supported zinc and paint combination, thickness ranges, layer interpretation, reference adjustments and treatment of unresolved results. Keep the manufacturer's manual revision in the inspection record.
Check references and report the actual method
Use the coating gauge reference-check workflow for the general distinction between verification and permitted application adjustment. For a duplex task, add the actual layer-related references and checks specified by the selected system.
Retain the gauge and probe identity, material construction, measurement stage, point location, sensor mode, reference observations, individual results and required statistical summary. If a result is calculated by subtraction, preserve both inputs and their identities alongside the calculated value.
When the observed layer structure conflicts with the instrument interpretation, investigate the construction and reference conditions. A prepared cross-section or another agreed method may supply the needed independent evidence. Obtain authorization for any destructive preparation and preserve its correspondence with the original inspection location.
Request a configuration for the complete layer system
Tell the supplier whether the inspection needs total coating, paint alone, zinc alone or all three. Include the zinc process, paint system, thickness range, shape, accessible reference surfaces and required acceptance method. Explain whether matched pre-paint observations are available.

Compare current options in the Mcooh thickness gauge collection against that layer-specific request. Ask for an actual sample demonstration when separate paint and zinc reporting is essential, with the exact probe, settings and reference conditions preserved in the resulting evidence.